Audi 80/90/Coupe
+ 1.2. Identification of the car
+ 2. Engines, carburetors
3. Lubrication system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Exhaust system
+ 7. System of ignition
+ 8. Transmission
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. Steering
- 12. Body, salon
12.2. Central section of a guard
12.3. Cowl rope
12.4. Forward guard
12.5. Forward wing
12.6. Lock pins of a cowl, rubber shock-absorber
12.7. Cowl
12.8. Gas-filled rack (Sedan models)
12.9. Trunk lid
12:10. Back door (Coupet's model)
12:11. Forward door, lower door loop
12:12. Adjustment of a window and the bearing door element
12:13. The window condensing traffic jams, the window regulator
12:14. Door lock
12:15. Draft of lever transfer of the lock
12:16. Rope of the internal door lock
12:17. Rotary clamp, adjusting spring
12:18. Adjustment of doors
12:19. The bearing door element
12:20. Central lock
12:21. The pump with two modes of forcing
12:22. Leading activator
12:23. Activator of a back door
12:24. Trunk lid activator
12:25. Activator of a cover of the fuel tank
12:26. Door glass (Coupet's model)
12:27. Adjustment of a butt slip (Coupet's model)
12:28. Framework of a back door, lower loop of a door
12:29. The bearing element of a back door, the condensing stopper
12:30. Rope, hinged lever
12:31. Door handle
12:32. Holder of components of a door
12:33. Hatch
12:34. Bumper casing
12:35. Sealing of a rear bumper
12:36. The extending clamp
12:37. Forward spoiler / laying of a niche of a wheel (Coupet's model)
12:38. Top overlay of a forward spoiler (Coupet's model)
12:39. Back spoiler / laying of a niche of a wheel
12:40. Rear bumper (Coupet's model)
12:41. Window regulators
12:42. Internal finishing of a body
12:43. Sitting
+ 13. Air conditioning system
+ 14. Electric equipment
|
Back door in assembly (Coupet's model)
1. Six-sided nut, 8 N. of m.
2. Locking plate; has the contact switch of a lamp of a luggage carrier
3. A bolt with a flat head and a washer, 4 N. of m.
4. Adjusting washer
5. The condensing laying
6. Lock washer
7. Hinge
8. Laying
9. Six-sided nut, 21 N. of m. |
10. Basis
11. Hinge axis
12. Washer
13. Bolt, 10 N. of m.
14. Gas-filled rack
15. Clip, 10 N. of m.
16. Bolt; onboard a body
17. Washer; onboard a body
18. Sealing ring; onboard a body
19. Clip; on the body boat |
Back door, removal (Coupet's model)
| PERFORMANCE ORDER |
| 1) remove a decorative covering from a frame of a back part of a roof |
| 2) remove a decorative covering of a back door |
| 3) disconnect a screen wiper of back glass |
| 4) remove a plait of wires from a back door |
5) extend a block cable connector of a screen wiper of back glass from a cavity
Prevention
For simplification of installation of the flexible pipeline of a washer, attach it to a back door a wire.
|
| 6) disconnect a jet of a washer and remove the pipeline |
|
Back door, installation (Coupet's model)
Carry out installation upside-down.
Back door, assembly
1. The condensing laying of a groove of a window
removal is possible only at the bracket removed from a door
2. 8 N. of m.
3. The condensing laying
it is fixed by means of the AKD 476 KD5 05 all-purpose adhesive
4. Door covering
5. The extending clamp
6. Shock-proof fittings
7. 8 N. of m.
8. The lower loop of the lock with the limiter of opening of a door |
9. Top loop of a door
10. 30 N. of m.
11. Overlay of a groove of a door
only on Audi-90 models
for removal pull out from the top part of an upholstery of a door
installation: clear a groove by means of a cleaner
place the pressurizing substance 3.0 mm thick in a groove
establish a slip on a covering of a door and pressure her for installation in the relevant provision |
Side part of a body
Arrangement of elements
| PERFORMANCE ORDER |
| 1) press on 1 against the stop |
| 2) tighten the screw 2 with an internal hexagon of 0.4 N. of m. |
| 3) close the hatch for installation of all components in initial situation |
| 4) tighten the screw with an internal hexagon of 6 N. of m. |
|
Back door, adjustment
Arrangement of elements
| PERFORMANCE ORDER |
| 1) adjust a locking plate 1 to and = 12.0±1.0 mm |
| 2) tighten 2 with m 0.4 N.' moment. |
| 3) close a back door for installation of all components in initial situation |
| 4) open a back door and tighten 2 with m 6 N.' moment. |
|
Lock of a back door, assembly (Coupet's model)
1. Locking plate
contains the contact switch of a lamp of a luggage carrier
adjustment: place a locking plate in the center and tighten with the moment 0.8 N. of m.
close a luggage carrier for centering and alignment of a locking plate
slightly slightly open and tighten six-sided nuts of a shock plate
2. Six-sided nut, 8 N. of m.
3. Draft of lever transfer
do not establish with a tension; maximum free wheeling of 2.0 mm |
4. Transitional plug
5. Plug
6. Laying
7. Plug
displace it for fixing of draft of lever transfer
8. Six-sided nut, 4 N. of m.
9. Lock cylinder
10. Lock
11. Six-sided nut, 8 N. of m. |
|
|