Audi 80/90/Coupe
+ 1.2. Identification of the car
+ 2. Engines, carburetors
3. Lubrication system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Exhaust system
+ 7. System of ignition
+ 8. Transmission
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. Steering
- 12. Body, salon
12.2. Central section of a guard
12.3. Cowl rope
12.4. Forward guard
12.5. Forward wing
12.6. Lock pins of a cowl, rubber shock-absorber
12.7. Cowl
12.8. Gas-filled rack (Sedan models)
12.9. Trunk lid
12:10. Back door (Coupet's model)
12:11. Forward door, lower door loop
12:12. Adjustment of a window and the bearing door element
12:13. The window condensing traffic jams, the window regulator
12:14. Door lock
12:15. Draft of lever transfer of the lock
12:16. Rope of the internal door lock
12:17. Rotary clamp, adjusting spring
12:18. Adjustment of doors
12:19. The bearing door element
12:20. Central lock
12:21. The pump with two modes of forcing
12:22. Leading activator
12:23. Activator of a back door
12:24. Trunk lid activator
12:25. Activator of a cover of the fuel tank
12:26. Door glass (Coupet's model)
12:27. Adjustment of a butt slip (Coupet's model)
12:28. Framework of a back door, lower loop of a door
12:29. The bearing element of a back door, the condensing stopper
12:30. Rope, hinged lever
12:31. Door handle
12:32. Holder of components of a door
12:33. Hatch
12:34. Bumper casing
12:35. Sealing of a rear bumper
12:36. The extending clamp
12:37. Forward spoiler / laying of a niche of a wheel (Coupet's model)
12:38. Top overlay of a forward spoiler (Coupet's model)
12:39. Back spoiler / laying of a niche of a wheel
12:40. Rear bumper (Coupet's model)
12:41. Window regulators
12:42. Internal finishing of a body
12:43. Sitting
+ 13. Air conditioning system
+ 14. Electric equipment
|
Trunk lid, hinge, rack (Sedan models)
1. Trunk lid limiter
2. The hinged limiter, in the closed position
3. Insulating washer
4. Combinational bolt, 21 N. of m. |
5. The fixing clip
6. Gas-filled rack
7. Six-sided nut, 21 N. of m. |
Trunk lid, adjusting gap
Placement of the sizes
|
Size
|
Adjustment
|
|
and = 4.4 + 1.0 mm
| Adjust the hinge |
|
b = 6.5 + 1.0 mm
| Adjustment it is carried out when changing the triangular panel |
|
with = 9.9 + 1.0 mm
| It is regulated by the shift of stoplights |
|
d = 8.0 + 1.0 mm
|
|
е = 9.75 + 1.0 mm
| Adjustment is made on a locking plate of a trunk lid |
The locking mechanism of a trunk lid in assembly (Sedan model)
1. A sealing ring for the lock cylinder
2. Draft of lever transfer
adjustment: place the lock and the cylinder of the lock so that in draft of rachazhny transfer there was no free wheeling; fix draft of lever transfer on the lock and record
3. The jointed plug
4. Spring washer
5. A bolt with a six-sided head
6 N of m.
6. Spring pin
7. Clown
remove carefully not to lose a spring ball
8. A bolt with a six-sided head
3 N of m.
9. Washer
10. Locking plate of the door lock |
11. A sealant, tear off a lining and paste on a shock plate of the door lock
12. Lock-nut, 3 N. of m.
13. Lock
14. A sealant, tear off a lining and paste on the lock
15. Lock cylinder
for removal pull out a spring pin, remove the clown and by means of a key squeeze out the lock cylinder
16. Sealing ring
17. Lock
18. Spring
19. A spring ball, cover it with lubricant before installation in the lock cylinder |
|
|