Audi 80/90/Coupe
+ 1.2. Identification of the car
+ 2. Engines, carburetors
3. Lubrication system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Exhaust system
+ 7. System of ignition
+ 8. Transmission
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. Steering
- 12. Body, salon
12.2. Central section of a guard
12.3. Cowl rope
12.4. Forward guard
12.5. Forward wing
12.6. Lock pins of a cowl, rubber shock-absorber
12.7. Cowl
12.8. Gas-filled rack (Sedan models)
12.9. Trunk lid
12:10. Back door (Coupet's model)
12:11. Forward door, lower door loop
12:12. Adjustment of a window and the bearing door element
12:13. The window condensing traffic jams, the window regulator
12:14. Door lock
12:15. Draft of lever transfer of the lock
12:16. Rope of the internal door lock
12:17. Rotary clamp, adjusting spring
12:18. Adjustment of doors
12:19. The bearing door element
12:20. Central lock
12:21. The pump with two modes of forcing
12:22. Leading activator
12:23. Activator of a back door
12:24. Trunk lid activator
12:25. Activator of a cover of the fuel tank
12:26. Door glass (Coupet's model)
12:27. Adjustment of a butt slip (Coupet's model)
12:28. Framework of a back door, lower loop of a door
12:29. The bearing element of a back door, the condensing stopper
12:30. Rope, hinged lever
12:31. Door handle
12:32. Holder of components of a door
12:33. Hatch
12:34. Bumper casing
12:35. Sealing of a rear bumper
12:36. The extending clamp
12:37. Forward spoiler / laying of a niche of a wheel (Coupet's model)
12:38. Top overlay of a forward spoiler (Coupet's model)
12:39. Back spoiler / laying of a niche of a wheel
12:40. Rear bumper (Coupet's model)
12:41. Window regulators
12:42. Internal finishing of a body
12:43. Sitting
+ 13. Air conditioning system
+ 14. Electric equipment
|
Front bumper, assembly
1. 30 N. of m.
2. 23 N. of m.
3. Absorber of shock loading
4. Bumper crossbeam
for removal it is necessary to remove a bumper casing
5. The central decorative
strip
removal: pull out from under the fixing pads (the bumper has to be sorted, and the crossbeam is removed)
6. Broad nut
7. Towing hook
8. The marked openings | 9. Holder of registration plate
10. M5x12 bolts
11. Decorative facing (5 cylinders)
12. Decorative facing (4 cylinders)
13. Bumper casing
14. The extending clamp
15. Plastic nut
16. Rubber washer
17. Decorative strip
18. Cover
19. Arm
20. 30 N. of m.
21. Guide |
Bumper casing, removal
| PERFORMANCE ORDER |
| 1) remove the extending fixing agents (insert) |
| 2) disconnect from a guide and press for the ends in the direction (arrow A) down |
| 3) remove a cover from a decorative strip and unscrew bolts |
| 4) disconnect the fixing pads from a bumper crossbeam |
| 5) remove decorative facing in the direction specified by an arrow B |
|
Towing hook, installation
|
|
1. Rivet
2. Prekladina
3. Kronsheyn of the towing hatch
|
Arm, installation
|
|
1. Crossbeam
2. Rivet
3. Arm
|
On all-wheel drive models the left absorber of shock loading fastens to a cross-piece an additional bolt. Tighten this bolt until 23 N. of m.
Front bumper, assembly (Coupet's model)
|
1. A bolt with a six-sided head, 23 N. of m.
2. Washer
3. Blow absorber
removal: remove a bumper
unscrew bolts with a six-sided head
4. Washer
three washers on each absorber
5. Bolts with a six-sided head, 23 N. of m.
6. Washer
7. A bolt with a ploskokonichesky head, 23 N. of m.
8. Spoiler
removal: remove a bumper
remove the extending clamps
unscrew a spoiler from a wheel niche
unscrew the top fixing bolts on a spoiler
disconnect washers of forward headlights if they are established
remove a spoiler, having pulled out it directly from a body
9. Fog light
if it is established, then there is no need to remove it during removal of a spoiler
10. Bumper crossbeam
for removal it is necessary to remove first of all a casing of a bumper and a decorative covering
|
11. Decorative strip
12. Bumper casing
it is possible to remove after the bumper is disconnected
13. M 6 N.' bolt / washer.
14. Arm
in installation time the spoiler needs to be established on an arm
15. M 6 N.' bolt / washer.
16. Washer
17. M 1,0 N.' screw.
18. The self-cut screw with a ploskokonichesky head
19. Holder of registration plate
20. Nut
21. Washer
remove a bumper
from within unscrew bolts with a six-sided head
in front remove a washer jet
22. Six-sided nut
the headlight washer jet fixes |
|
|